How to install strap buttons on a ukulele

By | January 13, 2015

The first thing I do with every ukulele I’ve purchased is install strap buttons. Strap buttons are the metal bits that you can hook a guitar strap on. Unfortunately, most ukuleles do not come with strap buttons. The traditional way to hold a ukulele has it squished between your right arm at the bend of your elbow and chest. If you find this awkward and uncomfortable, as I do, you’ll want to use a strap.

Before we begin, its worth mentioning the many ukulele strap options that don’t need installation. See the post at that link for details.

black strap buttonsChoosing Strap Buttons

Strap buttons typically come in chrome, gold and black. You’ll want these to match the existing hardware on your ukulele. You can match them to the tuner hardware or tuning pegs.

Be sure to select buttons that come with 1) the screw needed to install and 2) felt washers to give padding between the metal hardware and the instrument. The felt is optional but adds some protection to your instrument. By the way, pretty much all strap buttons will say they’re for guitar. That’s OK.

Amazon has good deals on strap buttons that come with felt and screws in chrome, gold and black.

Installing Strap Buttons

Once you’ve got your strap buttons, follow these steps to install them:

  1. Drill, baby, drill. The screws that come with your strap buttons go directly into your ukulele’s wood. Don’t worry, though – this isn’t nearly as scary as it sounds.
    • Use the correct size drill bit based on the screws provided with your strap buttons. The drill bit should be as big or slightly bigger than the core of the screw, but smaller than the threads. Using too large a bit may leave the screw too loose, while too small of a bit could crack the wood! If you’re not sure, start small and go one size bigger if the screw feels too tight.
    • Measure how deep you need to go by putting tape on the bit marking the length based on the screws provided. The tailpin screw will probably go all the way through, but the hole in the neck shouldn’t go any deeper than necessary.
    • The button on the bottom of your uke should go on the very center of the bottom of the instrument. This placement is important as (almost all) ukuleles have a thicker piece of wood there. Depending on your uke, you may be able to see this by peering into the sound hole. If there’s no extra wood there, you’ll want to use one of the alternative straps mentioned above.
    • The button on the neck of your uke should go at the base of the neck, where the neck is thickest. It should go on the bottom side of the neck when you’re holding it. So if you’re a right-handed (standard) player, that would be on the right side of the instrument when facing the sound hole.
  2. Once you’ve drilled your holes, insert the screws with a screwdriver. Use a simple handheld screw driver instead of a power tool so you have a sense of whether the screw is too tight. The screw should first go through the strap button, then through the felt washer and finally into your ukulele.

hootenany strapSelecting a Strap

For the most part, guitar straps will work on a ukulele. After all, you installed guitar strap buttons! When selecting a strap for your ukulele, the only catch might be length. Some guitar straps are pretty long and may not go short enough for use with your uke, especially if you’re a small person. Here are some classy straps that I recommend:


If you prefer watching video, this one has everything you need to know.

11 thoughts on “How to install strap buttons on a ukulele

  1. Greg Ash

    Excellent video!!!! It provided everything I needed to install my strap button on the heal. Mahalo nui loa!!!

  2. jack

    Great instructions, great workmanship: exactly what I was looking for and needed. About that background music though…. 🙂

  3. Todd

    My Kala resonator uke has a decorative inlay at the bottom center. Do you recommend drilling at center or offset slightly to miss the inlay?

    1. Matt Post author

      Hi Todd. Most ukuleles have a bracing (a piece of wood) at the bottom that you are drilling into. You don’t want to drill into the thin wood without the bracing behind it because it won’t be strong enough to hold the strap button. At the same time, I’m not sure how the inlay would respond to drilling. If you look inside and see that the bracing is considerably wider than the inlay such that you could drill next to the inlay and still be in the bracing, that’s one option. Another option would be to try your luck at drilling the inlay. Yet another would be to consult a guitar tech and get their opinion and/or have them do it.

    2. Lan Yarbrough

      Your choice.
      If it were mine, I would put it straight through in the normal position. (If you offset it, it may not feel the same and you will have many wasteful converaations explaining your choice to others.)
      To protect the inlay, I would suggest using sharp, new(er) drill bits, taping the area first, and drilling first and undersized piliot hole then the real one. Go slow and steady on this one. The heel of the neck hole should be much quicker.

    1. Rodger

      If you aren’t comfortable doing it yourself go to your local guitar shop. A place around the corner from me quoted $15 for the part and labor.
      There are lots of alternative methods for ukulele straps, all work, but the cenvetional buttons are my favorite. That way you can get super cool straps.

  4. Regena

    Thank you, we did it!!! has some great prices on straps.

  5. Pingback: PLUC Tips – Gail | People of Lewisham's Ukulele Club

Leave a Reply

Your email address will not be published. Required fields are marked *